1.配頁
1. Distribution page
配頁即將折好的書帖從中間一帖依次套疊在一起，后把封面覆套在上面。
The book posts whose pages are about to be folded are stacked together one by one from the middle, and then the cover is covered on it.
采用騎馬訂裝訂的書籍，厚度不宜過厚，否則鐵絲無法穿透，頁數多只能100頁。因此，采用騎馬訂裝訂的書籍一般需添頁的貯帖組不會超過8組。添頁到貯帖斗里時，應盡量將一摞書頁整理整齊，讓書頁之間能進入空氣，避免因堆積時間久或靜電原因引起下頁時粘連，進而影響開機速度。
For books bound by horse riding, the thickness should not be too thick, otherwise the iron wire cannot penetrate, and the number of pages is more than 100. Therefore, the book bound by horse riding binding generally needs no more than 8 groups of storage posts. When adding pages to the storage bucket, try to tidy up a pile of pages so that air can enter between the pages to avoid adhesion on the next page due to long stacking time or static electricity, which will affect the startup speed.
另外，對于前工序碼臺不平的書頁，應該在續添書頁時，將書頁整理平齊，以免在生產過程中造成停機現象，影響生產速度和產量。有時由于天氣干燥等原因，書頁之間會產生靜電，此時需在書頁周圍灑些水或者用加濕器進行加濕處理，解除靜電干擾。續添封面時要注意有無倒頭、白頁、雙張等問題。
In addition, for the uneven pages of the code table in the previous process, the pages should be sorted and leveled when adding pages, so as not to cause shutdown in the production process and affect the production speed and output. Sometimes due to dry weather and other reasons, static electricity will be generated between the pages. At this time, it is necessary to sprinkle some water around the pages or humidify with a humidifier to remove the static interference. When adding the cover, pay attention to whether there are inverted, white pages, double sheets, etc.
2.訂書
2. Book ordering
訂書過程中，根據紙張的厚度和材質，鐵絲直徑一般為0.2～0.7mm，訂位為兩釘釘鋸?fù)庥喲劬鄷旧舷赂?/4處，允許誤差在±3.0mm內。訂書時要求無壞釘、漏釘及重釘;書冊整齊、干凈;訂腳平整、牢固;訂距均勻并在折縫線上;書帖歪斜誤差≤2.0mm。訂書過程中要經常檢查所訂書冊是否符合標準要求，發現問題后應及時停機處理。
In the process of stapling, according to the thickness and material of the paper, the diameter of the iron wire is generally 0.2 ~ 0.7mm, and the positioning is two nail saw. The outer fixing eye is 1 / 4 from the top and bottom of the book block, and the allowable error is within ± 3.0mm. No broken nails, missing nails and heavy nails are required when stapling; The books are neat and clean; The binding foot shall be flat and firm; Set the distance evenly and on the crease line; The deviation error of the book is ≤ 2.0mm. In the process of book ordering, it is necessary to regularly check whether the book ordered meets the standard requirements, and stop the machine in time after finding problems.

3.裁切
3. Cutting
裁切時，應根據書籍尺寸大小和厚度，及時更換刀條，保證裁切出的書籍無出血、無刀花、無連頁、無嚴重破口，成品裁切歪斜誤差≤1.5mm。
During cutting, the knife strip shall be replaced in time according to the size and thickness of the book to ensure that the cut book has no bleeding, knife flower, page connection and serious breach, and the cutting skew error of the finished product is ≤ 1.5mm.
4.打包
4. Packing
打包前應檢查成品質量，要求全書光潔整齊，無明顯八字皺褶、死折、殘頁、臟跡等現象;頁碼順序正確，以頁碼中心點為準，向里或向外誤差≤0.5mm。收書碼臺上，要將書整理整齊，然后用堆積機打包成書，要求計數準確后再進行打包、粘貼標簽。
The quality of finished products shall be checked before packaging. The whole book shall be clean and tidy without obvious eight character folds, dead folds, residual pages, dirty marks, etc; The page number sequence is correct, subject to the center point of the page number, and the inward or outward error is ≤ 0.5mm. On the book receiving code table, the books shall be neatly sorted, and then packed into books with a stacker. It is required to pack and paste labels after accurate counting.
以上的精彩內容來自：濟南書刊雜志印刷更多的精彩內容來自：http://www.aozhouhui.com歡迎大家與我們進行交流。
The above wonderful content comes from Jinan leaflet printing, and more wonderful content comes from: http://www.aozhouhui.com Welcome to communicate with us.